1. Process cannot be used for producing a crank shaft is
A. casting
B. rolling
C. welding
D. bending
Answer - Option B
2. A poppet value can be produced by
A. rolling
B. swagging
C. combine forging and extrusion
D. stretching
Answer - Option D
3. Needle is produced by
A. swagging
B. extrusion
C. machining
D. forging
Answer - Option A
4. Metal not good for impact extrusion is
A. alloys of Zn and Sn
B. stainless steel
C. low carbon annealed steel
D. alloys of aluminium and lead
Answer - Option B
5. Material good for extrusion is
A. stainless steel
B. brass casting
C. low carbon annealed steel
D. low carbon work hardened steel
Answer - Option C
6. In which forging machine anvil on which work piece is placed moves toward descending punch ?
A. Board drop hammer
B. Air lift hammer
C. Trip hammer
D. High energy rate forging machine
Answer - Option D
7. Upsetting or cold heading is a
A. rolling process
B. extruding process
C. bending process
D. forging process
Answer - Option D
8. For extrusion process
A. complex sections are produced from bar stocks
B. good surface finish and close tolerance is generated
C. the strength of finished product is improved due to cold working
D. all of these
Answer - Option D
9. Forming process which does not involve rotation of work piece is
A. spinning
B. thread rolling
C. upsetting
D. ring rolling
Answer - Option C
10. Different steps in Blocking, which is finishing operationin forging are in the following operation in forging are in the following order
A. coining, trimming, planishing
B. trimming, planishing, coining
C. planishing, coining, trimming
D. planishing, trimming, coining
Answer - Option B
11. The operation that removes fins and flashes from a forged part is
A. combination of trimming, planishing and coining
B. combination of trimming and planishing
C. combination of planishing and coining
D. trimming
Answer - Option D
12. A hack saw blade cut on
A. forward stroke
B. return stroke
C. both (a) and (b)
D. depends upon direction of forces
Answer - Option A
13. The forge hammers used for planishing and coining are
A. Air lift hammers
B. Helve and trip hammers
C. Board drop hammers
D. Steam hammers
Answer - Option B
<strong14. The major problem in hot extrusion is
A. design of punch
B. design of die
C. wear and tear of die
D. wear of punch
Answer - Option C
15. Extension process can effectively reduce the cost of product through
A. material saving
B. process in tooling cost
C. saving in tooling cost
D. saving in administrative cost
Answer - Option A
16. In a solid extrusion die, purpose of knock out pin is
A. shopping the part to extrude through the hose
B. ejecting the part after extrusion
C. allowing the job to have better surface finish
D. reducing the waste of material
Answer - Option B
17. Width of slot cut by a hacksaw blade as compared to width of blade is
A. more
B. less
C. equal
D. none of these
Answer - Option A
18. Length of hacksaw blade is measured from
A. center of hole at one end to the center of hole at the other end
B. extreme end to extreme end
C. 16 times the width
D. none of these
Answer - Option B
19. Hacksaw blade is specified by its
A. width
B. length
C. material
D. number of teeth
Answer - Option B
20. Hacksaw blade preferred for cutting brass have number of teeth
A. 14 per inch
B. 25 per inch
C. 32 per inch
D. 40 per inch
Answer - Option A
21. Teeth of hacksaw blades are bend
A. alternately right or left and every third or fourth left straight
B. towards right
C. towards left
D. none of these
Answer - Option A
22. A file with 20 teeth per inch is known as
A. rough file
B. smooth file
C. bastard file
D. second cut file
Answer - Option A
23. A file removes metal during its
A. forward stroke
B. return stroke
C. both (a) and (b)
D. none of these
Answer - Option A
24. File used for wood work is
A. single cut file
B. double cut file
C. rasp cut file
D. none of these
Answer - Option C
25. Slip gauges are made of
A. cast iron
B. aluminium
C. alloy steel
D. copper
Answer - Option C